How to Get Furniture Polish off an LCD TV Screen

An LCD TV screen is very attractive, but it sometimes can become dirty fast. You should keep it clean but also realize that you need to purchase the right cleaners and use the right cleaning methods.

Otherwise, you could risk the chance of damaging your TV screen. If you do not want to purchase a commercial cleaner sometimes a homemade solution can be used.

Supplies Needed

To clean your LCD TV screen you need distilled water, isopropyl alcohol (70% concentration), spray bottle, and microfiber cloth. You would apply these ingredients and supplies throughout the course of removing dirt, grime, and other gunk from your television.

If you want to remove stains from your LCD stain you should use the following guidelines:

1. You should unplug your television. It should not be connected to any power strip, outlet, or device that gives off power.
2. Now it is time to prepare your cleaning solution. You can mix equal parts of distilled water and alcohol in a spray bottle. However, do NOT spray the solution directly on your LCD screen! Or you could damage it. Instead, refer to the next step.
3. When you spray the microfiber cloth with a cleaning solution it should be slightly damp, not dripping wet. Otherwise, just like if you were to spray the cleaning solution on the LCD monitor you could ruin it.
4. When you wipe your LCD monitor use only gentle pressure. For best results, wipe in the same direction all the way across from the top down. This will help avoid streaks as you clean the screen.
5. Sometimes more than one cleaning is necessary for removing all of the dirt and grime from your LCD screen. Still, each time be careful and do not press hard.
6. One you are finished, you are advised to wait a few moments for the screen to dry. Then, once you know its dry you can plug the television back in.

More Advice

Additional products and cleaning methods may be needed. However, you should be careful that they are products meant for LCD monitors. Certain kinds of cleaners meant for eyeglasses or cell phone screens might possibly be appropriate, but never use window cleaner.

You could find certain wipes that are sold in stores that are made especially for LCD monitors. You should really use these over any other commercial product. To be on the safe side, you should pay attention to the care guidelines provided by the manufacturer of your television.

As far as cleaning kits, sometimes they may even be provided with televisions when you purchase them. However, if you never received one maybe you can go back to the store where you purchased your TV. They may have a selection of cleaning kits and products made for your brand of television.

If you have any questions regarding television cleaning solutions maybe you should ask a sales person in the electronics department. This is the best way to find out how you can clean your prized home theatre electronic device while prolonging the life of it rather than reducing the life of it.

How to Clean the Wii Fit Balance Board

The Wii Fit Balance Board is meant to be used barefoot. You know what this means though. It means you have to learn how to clean the Wii Fit Balance Board correctly so it works the way it should.

You also have to learn how to clean this popular gaming piece so you can prolong the life of it. The more you learn about how to clean this popular Wii toy the longer it will last. In other words, if you take good care of it you will get more uses out of it than if you do not take care of it.

IIImportance of Cleaning:

One reason that it is very important to clean your Wii Balance Board is because it can attract germs. These germs can cause serious problems, such as Athlete’s Foot.

A second very good reason for cleaning your Wii Balance Board is to avoid any damage to it. You can also cover it with silicone sleeves in order to further prevent damage.

Supplies Needed:

To clean the Wii Fit Balance Board you need a soft lint-free clothr and some disposable disinfectant wipes. Clorox wipes are highly recommended but just about any kind of brand of disinfectant wipes would work.
The Wii Balance Board cleaning process is shown below:

1. Take the lint free cloth and use it to remove as much dirt and grime as possible.
2. After you have wiped the Balance Board with a lint free cloth you should use a disinfectant wipe to sanitize it.
3. No dampness or residue should be left on your Balance Board. You can inspect it before and after cleaning it just to be sure.

When cleaning your Balance Board silicone sleeves you should follow these tips:

• You are advised to never twist or wring out the silicone sleeves when washing.
• All soap residue should be rinsed from the sleeve or it could cause the silicone material to become too worn out.
• No bleach or bleach alternative should be used when washing the sleeve.
• Before you replace the Wii Fit Balance Board liquid accumulation can damage it.
• Remember that harsh cleaning pads and abrasive cleaners can damage your Balance Board and/or protective sleeves. Never use anything but what is specifically recommended for your these Wii accessories.
• Continue to sanitize your Wii Balance Board after each new player uses it. This will further prevent the spread of germs.
• One way to keep your Balance Board clean is to use the recommended Wipe All Purpose Eco-Friendly wipes. However, you should look on your device and accessory packaging labels to verify what wipes are safe to use.
• Silicone sleeves are useful for protecting your Wii Fit Balance Board. However, it is recommended that you use the sleeves that are specifically designed with this popular gaming accessory.

Additional Advice:You are advised not to use a liquid-based cleanser or detergent to clean your Balance Board. Otherwise, you could damage the components inside it. You should also never use water to clean this very important Wii accessory, nor should you submerge it in water.

How to Clean an iPod Hold Button

An iPod hold button often gets very dirty. This dirt and grime that builds up is often a result of touching your device after eating, using the restroom, covering a cough, etc. After awhile, your device becomes a magnent for germs.

With all these reasons and occassions to dirty your entertainment device’s hold button, a good method of cleaning is needed. A dry cleaning method is recommended, and the steps for this dirt removal process is shown below.

Supplies Needed:

You need soft cloths, cotton balls, or cotton swabs. You also need toothpicks. These items will be used in various stages of the iPod hold button cleaning process.

Here are the steps to clean the button:

1. Get out a cotton swab and gently wipe the area around the button. If you want to remove the dirt from around the edges you can use a toothpick to gently scrape the dirt off.
2. Any dirt that comes loose can be wiped away with a cotton ball or cotton swab. Clean the button as well as possible with the dry cotton. Then, a slightly moistened ball or swab can be used to clean the button as long as you do not drench it and cause an electrical shortage to occur within your phone.
3. As far as cleaning the button of your iPod is concerned it is important to remember to use as little of the cleaning liquid or water as possible. Your swab or cotton ball should be just barely wet but not soaked, and it should only be used on the button exterior but not the button crack.
4. You may find variations of the above steps, but what you see above is a basic guide. The above steps along with the additional guideance shown below should really help you as you seek a way to keep your iPod looking like new. As a result, your device should be preserved for as long as possible.

More Advice:Cleaning an iPod hold button can improve the performance of your iPod most of the time. The one main exception is if the button itself is somehow malfunctioned. In this case no amount of dirt and grime removal is going to cause the iPod to work better.

The hope in this case is that your iPod still has a warranty. This will more than likely make replacing your iPod easier and less expensive. As far as replacing the hold button or repairing your multimedia device, this may require the assistance of a professional.

As far as alternative methods of cleaning, sometimes a toothbrush would help. It is highly recommended that you use a clean dry toothbrush though and perhaps you can save this brush for future iPod hold button cleanings.

The more often you clean this very important control button the better off you are because it will increase and prolong the functionality of your device. This will save you money in the long run as purchasing an entirely new iPod can be highly expensive.

How to Clean an iPhone

Cleaning your iPhone is a very simple procedure, but this is a task that should be done very carefully and slowly. You should not rush this process or you may not do as good of a job as you would if you take your time.

If you do this process right, your iPhone will last much longer. You will in the end be rewarded more for the tender loving care you give your phone.

Supplies Needed:

Some items you need for cleaning your iPhone include a microfiber or other lint-free cloth, cool water, and iPhone. This process should be done in a safe and quiet spot for best results.

Here are some steps for cleaning your iPhone:

1. Disconnect all USB cables from your iPhone. Never clean your iPhone while it is attached to a computer or other electronic device, and never clean it if it is being charged via power cord or docking station.
2. One extra step before cleaning your iPhone is to turn it off. Just press the sleep/wake button. You can look at your product instruction manual if you cannot find this shutoff button.
3. After three to four seconds a red slider will appear on your iPhone screen. All you need to do is use your finger to drag the red slider across the screen. Once you do this the iPhone should then be turned off. If not refer to your product instruction manual again or call a technician.
4. Dampen a small corner of soft microfiber cloth with just a little bit of water. Distilled water is recommended for this purpose but regular water can help as well. In any case, never apply any water or any cleaning solutions directly to your iPhone and make sure your microfiber cloth is only slightly damp, not soaked.
5. Use the dampened micofiber cloth corner to gently wipe the iPhone. When doing so, please pay special attention to the touch screen but avoid wiping the ports.
6. If your iPhone is especially dirty you should try to remove the surface dirt with a soft brush or compressed air brush. Then, you should proceed with using the dampened microfiber cloth.
7. After your device is cleaned and you are satisfied with that level of cleanliness you should use the dry portion of the cloth to remove excess moisture. Then, after your iPhone has completely dried you should turn it back on by pressing the sleep/awake button. You will know its back on with the “Apple” logo appears on the screen.
8. Repeat this process at least once a week. If you use your device frequently you can even do this up to once a day, or once every couple of days.

More Tips and Advice:Before you clean your iPhone you should take a look at your user’s manual. This is where you can find out all the information you need about features and recommendations concerning your iPhone.

This is where any manufacturer precautions regarding to cleaning your phone you come across can be found. Your iPhone usually comes with its own cleaning cloth but you should follow whatever recommendations are presented in the iPhone manual as well.

How to Clean a Shredder

A paper shredder is one of life’s most important machines. However, if you do not maintain it properly it could burn out and become unusable faster than you hoped.

Prevention is one of the first steps in cleaning and maintaining your paper shredder. However, it also helps to find a way to also cleanse it properly.

Preparation for Cleaning:

Before you clean your shredder you should make sure it is turned off and unplugged. If it is a battery-operated or otherwise powdered unit, you should remove the batteries. This is very important because you do not want to lose your fingers in the shredder while cleaning it.

After the machine is turned off you should then be able to disassemble it very easily. All you have to do is remove the lid from the main container but while doing so you should not try to force the pieces apart. Otherwise, you could risk breaking the machine.

If you are having any trouble removing the lid from the rest of the machine you may want to seek help. You may find answers in the owner’s manual or you might be able to call the manufacturer for assistance.

Just so you know, the shredder cleaning process should not require too much effort. After all, the hope is all that you put in it is paper, unless you have one that is equipped for shredding credit cards.

The steps for cleaning your shredder are shown below:

1. First, you would gather your supplies and mix your solution. As far as ink smudges or dust, that can be cleaned off with a cloth or paper towel and a preferred cleaning solution. You can either use a dish soap mixed with lukewarm water or you can use regular vinegar and rubbing alcohol.
2. If you decide to use the dish soap and water, mix the solution in a cereal bowl using your hands or a spoon. Then, dip a cloth into it or use a paper towel and wring it out tight.
3. If you would rather use the vinegar or rubbing alcohol just pour the solution directly on the cloth but not directly on the shredder. You should wring the moistened cloth out tight before you use it.
4. Use a clean and dry cloth or paper towel to wipe away any residue from the cleaning solution away. Then, let the machine air dry or you can use a dry paper towel or cloth to wipe away any left-behind moisture.

More Maintenance Advice:You do not need to clean your paper shredder out all the time. Just once in a while, or maybe a few times a year. Of course, the obvious exception is if you spill something on it.

The one thing you should do on a regular basis is oil your shredder. This should be done once a week, but maybe more often if you notice your shredder gets jammed too much. This is important because lack of lubrication is more than likely the cause of paper jams than is the machine being dirty.

How to Clean a Remote Control

A remote control can get dirty very easily. After all, everyone in your entire household, even your children or pets, may be touching it. Not to mention countless guests may have used it from time to time.

You should clean it regularly in order to ensure your family does not get sick, and you do not get sick. Regular maintenance of all your remote controls in fact can be quite helpful.

Preliminary Advice:Cleaning your remote is not a hard task. However, it requires that you be very careful. Otherwise, you could damage the battery contacts or the inner circuits.

It is important that you learn both tips to perform a quick surface cleaning and more in-depth cleaning of a remote. You also are advised to learn ways to clean both the inside and the outside of this remote control unit.

Here are the steps for cleaning your remote control:

1. Take apart the remote. When doing so be very careful. The first step of disassembly is to take out the batteries, then take a screwdriver and remove all the remote screws. These screws should be then put in a safe place, such as in a bowl, so you do not lose them. The batteries should be kept in the bowl as well. This is so you do not lose the pieces.
2. When the screws are removed, the remote should come apart very easily. A flat head screwdriver or knife can be used for this purpose to seperate two halves of the remote if it does not just easily come apart when you pry it with your hands.
3. As you dismantle the remove you may want to shake it around a bit after taking it apart. This is to ensure that no screws have fallen inside.
4. Pull out all the buttons from the circuit board and put them aside. Then, place the circuit board on a clean, dry surface. But if no surface is available place the remote control on a paper towel.
5. Cleaning the circuit board requires using the right kind of solution. Water should absolutely not be used for this cleaning job. Instead, either rubbing alcohol or commercial contact cleaner should be tried. These can be found at most electronic stores.
6. Usually you can spray a contact cleaner on if it comes in a spray bottle. Either that or you can use a cotton swab to gently wipe away any gunk with the rubbing alcohol. When doing so your swab should be intact and you should make sure no fuzz is left behind on the circuit board.
7. The best way to ensure that no fuzz is left behind by a cotton swab is to wet it just enough with the rubbing alcohol. That way, the cotton swab will be moist enough for application and moist enough not to leave fuzz behind.
8. Whencleaning the buttons of the remote, you should use a mixture of dish soap and water if you want. Otherwise, you can just use the rubbing alcohol. If you decide to use the dish soap mixture you can add about a teaspoon of dish soap to two cups of water and mix them together in a bowl.
9. If you want to scrub a keypad with a cotton swab or an old toothbrush you can let the buttons air dry. Otherwise, you can wipe them with a handkerchief, old t-shirt, or microfiber cloth to ensure the inside of the remote is not indundated with lint.
10. After everything is dry you should then put the remote back together and put the screws back in. After that, you should follow the steps below for a quick surface cleaning.

Surface Cleaning Guide:For this you would not take the unit apart. Instead, just simply wipe around the remote control with a cotton swab and rubbing alcohol to gently clean the crevices.

Likewise, the grime that is stuck between two halves of a remote can be removed using a toothpick. When using the toothpick make sure you get the top, bottom, and sides of the remote, as well as the battery compartment. For this the batteries should be left out of the remote until after this cleaning step is done.

HHow to Clean a Playstation 3

A PS3 and it’s corresponding wireless controllers often is dirty and smudged. The controllers are also sometimes very sticky and dirty. It is important to learn the correct way how to clean a Playstation 3.

Preliminary Step

It is very important that before you unplug your Playstation 3 from the wall that you remove all the cord connected to it. The memory cards and other accessories attached to it may also need to be removed.

The sSteps to cleaning your Playstation 3 console include as follows:

1.

1. Fingerprints and greasy smudges can be very easily removed. All you need is a gentle all-purpose cleaner or an ammonia-free glass cleaner. The cleaner should be sprayed on the rag instead of directly on the Playstation so you do not risk getting the solution into the vents.
2. Sometimes your Playstation 3 may be more dusty than normal. If it is, you should use a small narrow vacuum attachment to carefully suck out the dust from the vents. You can also finish this job with a toothbrush or cotton swab in order to remove all the stubborn dirt and grime.



3. While you wipe and scrub the dirtiest areas of your Playstation you should be careful not to get any liquid into the console itself. Skip the A/V and USB ports unless they are very gummed up and causing problems.

2.

If you want to clean your Playstation 3 wireless controllers you should use these steps:

1. Wipe down the controllers to remove dirt from the easy-to-reach areas of the console. A clean, damp cloth will do the trick, but make sure you wring out the cloth as thoroughly as possible.
2. In order to clean the cracks around the buttons a damp cotton swab is recommended. You could also scrub out these hard-to-reach areas with a toothbrush.
3. If you have spilled something sticky on the controller buttons, you may first have to very careful dismantle the controller and clean the button contacts. Wipe gently on the contacts until they feel smooth and free of dirt and grime. Be careful when doing this because otherwise your Playstation 3 warranty could be voided.
4. If you want to further clean your Playstation you should wipe it with alcohol pads. This will disinfect it so no sickness-causing germs can accumulate on it.

Now pay attention to what not to do:

You should never immerse your Playstation 3 or its contollers or any part of the console in water. You also should never use any harsh or abrasive chemicalls on the machine as the inside of the console and the finish could be damaged.

If you want to ensure that your Playstation 3 is not damage you may want to hire a professional to do the work for you. This would lessen the chance that your warranty would expire.

How to Clean a PSP

A PSP is a very popular gaming device and media player. However, it also sometimes is a huge collector of dirt, dust, grime, and debris. You need to learn how to clean a PSP correctly in order to prolong the life of it while minimizing the damage of it.

Supplies Needed:

In order to clean a PSP properly you should first gather all your materials. You are going to need a wooden or plastic toothpick and a cotton swab. You also should get a microfiber or lint-free cloth and some cool water.

Introduction :It is highly recommended that you clean your PSP in a safe and quiet spot. Also, when cleaning this entertainment device you should take your time. Taking the right action against dirt and grime can increase the number of hours of life of it.

The steps to clean a PSP are shown below:

1. Disconnect any cables or connectors that are plugged into your PSP. This includes headphones, games, movies, or discs. It is also highly advisable that you remove the battery from your PSP so you can clean it.
2. No computer or power supply should be connected to your PSP while you clean it. Otherwise, you could put yourself at a huge risk of getting an electric shock.
3. If you are unsure as to how to turn your PSP off you should take a look at the instruction manual. This will help you figure out how to power it off correctly as to prevent electric shock and prevent device damage.
4. After your PSP is successfully disconnected and powered off, you can begin to remove dirt from it. Some common problem areas include dirt lodged in the control buttons. A wooden toothpick is perfect for this job.
5. To clean the dirt lodged in the control buttons, all you need to do is rub the toothpick around the edges. Be careful not to press hard when doing this or you could damage the controls.
6. When cleaning out the dirt from your PSP a dry cotton swab is very useful for this purpose. All you have to do is gently remove all dirt or dust that has accumulated in the connectors (ports where plugs connect).
7. When attempting to clean your PSP you should dampen your cloth with cool water, never hot water. Furthermore, in the process of cleaning your PSP you should wring out the cloth as tight as possible, so it is barely damp.
8. Before you use your cloth to clean your PSP you should run it across a mirror or other glass surface. If you notice the water is left behind or it drips or runs the rag is still too wet to be used and then needs to be wrung out some more.
9. Using a barely damp cloth, you should gently wipe your PSP. When doing so you should wipe the screen well but at the same time you should avoid wiping the power port.

More Advice:Before you clean your PSP you should refer to your user’s manual. In it all the features and recommendations pertaining to cleaning and maintenance are found. Any precautions you need to take in regards to cleaning are found here as well.

You should realize also that in addition to the above cleaning tips you can wipe yoru PSP with a soft, dry (lint-free) cloth after each use. This will help cut down on the accumulation of dust and grime. You should never use paper towels on your PSP or they can cause small scratches.

How to Open and Clean a Harmony One Remote Control

The keys of a Logitech Harmony One remote control can become very sticky. This usually requires careful opening of this device.

It also helps if you know the proper supplies and steps needed for cleaning this kind of remote control. That way, you can prolong the life of this Harmony One device rather than shorten the life of it.

To clean off dirt, debris, food, and other dried-on remote control debris you will need:

Rubbing alcohol, cotton swabs, and a lint-free cloth. You also should gather some toothpicks.

Steps to clean your Logitech remote are shown below:

1. First take the batteries out of the remote control. No power should be running through your device while you clean it.
2. When cleaning out the gunk and grime from your remote you should concentrate on the buttons and the seam of the remote. This is where the most dirt builds up. You can use a toothpick for this scraping job.
3. For the stickiest areas rubbing alcohol can be used. Just dip a cotton swab in the solution and then excess liquid before using it to wipe away dirt.
4. You may need to grab a second or third swab for this purpose. This especially works for cleaning the seam in between the top and bottom halves of the remote, but it also works great on the buttons.
5. After removing all the dirt a lint-free cloth is needed. This will help wipe down the entire case.
6. Be careful while wiping your remote control. Just use only enough of the alcohol that you need to help you clean the unit, but not so much that you drench it
7. If you want to make sure that no alcohol has seeped into the interior of your remote, you can shake the remote before you reinstall the batteries. This will help ensure you do not short out the unit and ruin the batteries when you reinstall them.Pay careful attention to the above tips, which should take care of most of your problems. You can also take head some of the additional advice for cleaning and maintenance of your remote control as shown below.

Additional Advice:If you run across instructions on dismantling a remote control for cleaning this is not a recommended action to take. The remote is very fragile and could very easily break and the screen of it could very well not function right.

Besides, taking the remote apart could cause whatever warranty came to become void and then it cannot be easily serviced or replaced. If you really want the insides of the remote cleaned you should really take it to a professional repair person who can do it for you.

That way, if if anything is seriously wrong with it the situation can be resolved as fast as possible. This will help prevent any further damage to the remote and it will further increase the life of it.

Closing Thoughts:Cleaning your Harmony One remote control on a regular basis can help prolong the life of it immensely. However, there will come a time when you need to get rid of it and get a new one. Still, if you take proper care of the device you have now it will increase the chance of this device working for as long as possible.

How to Clean a Cell Phone

Oftentimes germs accumulate on phones when people talk on them. This happens while talking especially if we have a cold or other viral or bacteria mouth or respiratory sickness. Germs can also can tranfer from hands that have been in the pockets, or even running through the hair, or holding food.

Make-up and oils can also build up from our ears and faces. For this reason, some simple cleaning tips are recommended for removing all of this excess build-up. Before you learn what you need to do to clean your phone safely, you are going to be shown what supplies you need.

Supplies Needed:Disinfectant wipes, rubbing alcohol, and soft cloths are very helpful. The lint free cloths are the best bet for this project.

You are also advised to gather a soft-bristled brush, cotton swabs, and a small dish and some window cleaner. These items will be used throughout the steps you see below.

Here are the steps that are typically used for cleaning a cell phone:

1. Using a disinfectant wipe or soft cloth dampened with rubbing alcohol helps remove some built-up. Be gentle yet using a moderate amount of force while you rub build-up, sweat, and grime from the face of your phone.
2. The outer shell of your phone should be wiped with a second disinfectant wipe or alcohol-damped cloth. Just put a small amount of alcohol in a dish if you do not have any pre-moistened wipes.
3. If you want to use the wipes, pour a small amount of alcohol into a dipping bowl. Then either immerse a corner of a cloth, cotton swab, or bristled brush, and shake or squeeze off the excess liquid.
4. Rub the damp swab, cloth, or brush into the spaces around the phone keys. You can also use it in between all the crevices around the phone screen. The swab or brush will help you reach these tougher areas to clean.
5. A slightly dampened cloth can be used to clean round the charger connection. Be careful not to allow any liquid to seep into the inside of the phone’s battery terminal
6. Once all the dirt is removed from around the battery terminal, allow your device to dry completely. After this it should be ready to use.

More Advice:You should avoid spraying any cleaners on your phone. Otherwise, the excess moisture could damage your device. It would be better to spray the cleaner onto a soft cloth beforehand.

Another option would be to find cloths that are especially designed for cleaning phones. However, any disinfectant wipe would help. You are reminded not only to not allow any liquid to seep into the terminal and phone interior, but also do not allow the liquid to come in contact with the battery.

In other words, use enough water to clean your phone but not too much that the phone would be damaged. This will allow you to keep your phone free of dirt, grime, and debris without inhibiting phone functioning.

Other tips may be availalbe for keeping your phone looking sharp. However, the above tips should be a great start.

Next Page »